• 本课程为精品课,您可以登录eeworld继续观看:
  • UNGROUNDED CONDUCTORS - 310.6(C)​​​​​​​
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    用户评论

    暂时无评论

    猜您喜欢

    推荐帖子

    串口通信上位机怎么收不到数据啊
    #include "include.h"#include "msp430x14x.h"#include "string.h"#define nData 10unsigned char nRxBuff = 0;unsigned char buf[60];unsigned char cBuf[20];signed char RXTXstate;//发送数据计数unsigned char flags;/
    971626996 微控制器 MCU
    SPI read data via DMA fail?
    各位高手大家好~有個SPI DMA的問題請大家。小弟使用開發平台為STM32F103ZE。目前若不用DMA的SPI是正常可以使用的。但目前SPI傳的速度不夠快,若照SPI 6Mbps傳送4kB data應該約花5.3 ms,但是目前我從波形上量到的時間約是12~13ms, 因為我的應用上需要更快的速度,而Slave最快的SPI速度只有支援到 6 Mbps,所以ST的速度也沒辦法再快了@@而目前的沒
    willwu stm32/stm8
    WIN7环境下,新建一个文件夹重命名为AUX,会出现错误
    这是为什么呢?{:1_99:}
    MrKingMCU 聊聊、笑笑、闹闹
    请帮忙看看这个开关电源电路怎么滤波?
    如题,ACDC开关电源经过LDO输出5V电压,接下在怎么滤波啊?下面有我用的原理图和示波器采集的波形。
    kzero9 电源技术
    LOTO课2:二极管实践 --- 桥式全波整流
    实践用到的资源4个整流二极管,500R的电阻(做负载),示波器,信号源备注:阻值并不需要准确,这个电阻是作为负载使用的,阻值不能太大,太大的话会把电流限制到很小,可能让整流二极管截止,二极管焊接的时候注意极性。信号源要能产生正负2v以上频率50HZ的正弦交流信号视频中使用OSC482S自带信号源模块产生正负2V的正弦波作为二极管桥式电路的输入,通过示波器两通道分别检测输出端的端点电压,并通道相减显
    LOTO2018 移动便携
    我想在日历控件上(MFC的DateTimePicker控件)上弹出TAH(上下文菜单,类似pc上的右键弹出菜单),请问该如何实现,能给个例子吗?
    网上的例子都千篇一律的出自codeproject上一位葡萄牙工程师的论文,看了几遍都没看懂,里面很多函数参数不知从何而来.不知大哥能否给小弟指导一下?感激不尽
    yqivy 嵌入式系统

    推荐内容

    可能感兴趣器件

    EEWorld订阅号

    EEWorld服务号

    汽车开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2023 EEWORLD.com.cn, Inc. All rights reserved