• 本课程为精品课,您可以登录eeworld继续观看:
  • (b) APPLYING BOTH DERATING FACTORS TABLE 310.15(C)(1) AND TABLES 310.15(B)(1) AND (B)(2)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    【国民技术N32WB452测评】第二期、在RT-Thread完整版中点灯及ADC的使用
    [i=s] 本帖最后由 yang8555u 于 2022-7-27 13:35 编辑 [/i]上一次发帖,我曾经请教过论坛里的各位,想试图找到N32WB452的RT-Thread的完整版系统SDK,可惜收获的回答是No。在获得这个回答后,曾考虑过移植RT-Thread到N32WB452上,但发现,RTThread的官方移植的N32G457的SDK也是可以直接下到N32WB452里的,个人推测因为都
    yang8555u 无线连接
    想从基础学verilog,大家给指教一下
    本人菜鸟一个,大家给些意见。
    SUN2001111 FPGA/CPLD
    稳压
    这是单片机串口波形请问我要稳住在单片机极限电压5.5V用什么管比较好呢
    tangwei8802429 模拟电子
    EVC CListCtrl 闪烁的问题
    在定时器里 更新 CListCtrl里面的值,结果闪烁的特别厉害,谁见到过这中问题。如何解决的?请指教。
    munitis 嵌入式系统
    WinCE下evc怎么来检测自己的网络状况
    现在在程序界面上,想要做一个方块(红 绿 黄等),颜色的切换来表示 网络状况的好坏,如果不能表示好坏,来表示连接着或断开这两种也行,最好能像网卡上接网线的地方的指示灯一样的效果。不知怎么~~~处理
    Prefer 嵌入式系统
    【MSP430 编译器使用经验】-使用CCS优化msp430的设计与编译
    [align=left]目录[/align][align=left] [/align][align=left]1 概述 1[/align][align=left]2 ULP Advisor[font=仿宋_GB2312]简介与优化流程[/font] 2[/align][align=left]2.1. ULP Advisor[font=仿宋_GB2312]简介[/font] 2[/align][al
    mars4zhu 微控制器 MCU

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved