• 本课程为精品课,您可以登录eeworld继续观看:
  • HIGH LEG IDENTIFICATION - 408.3(F)(1)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    用户评论

    暂时无评论

    猜您喜欢

    推荐帖子

    Illegal loc on PAD symbol,IPAD_IBUFG only be loced to GclkIOB site syn_nockbuf
    [size=12pt][font=Times New Roman]1.[/font][/size][font=宋体][size=12pt]在分配完管脚后,出现‘[/size][/font][size=12pt][font=Times New Roman]Illegal loc on PAD symbol,IPAD_IBUFG only be loced to GclkIOB site syn_no
    cjfwindy FPGA/CPLD
    卖开光加持版KW41!
    没错,就是论坛之前活动的KW41!KW41一分钱不收,蜀黍开光加持费只要人民币600!只要拿着一天,zigbee无师全通,只要拿着两天,ble自然贯通,仅此一套,手慢无,要的来,不刀不包邮。
    freebsder 淘e淘
    常用74系列芯片功能速查
    [b][color=#0000ff][font=宋体]一些74系列芯片的资料。[/font][/color][/b]
    fengxin PCB设计
    能解释一下标红处什么意思吗?PWM怎么控制开关的?
    voidComHandler(void){TIM1->BKR &= (uint8_t)(~TIM1_BKR_MOE);//禁止PWM输出PWM_A_OFF;PWM_B_OFF;PWM_C_OFF;if(FaultF!=0||St_F==0)return;if(bHallStartStep==0)//AB{[color=#ff0000]TIM1->CCR1H = (uint8_t)(OutPwmVa
    KCP stm32/stm8
    MSP430+24L01做成的记录器,读卡器一对多如何识别?
    记录器里的24L01在不读数时的时段都是关闭着的,只有读卡器要对其进行数据读写时才会打开24L01。读卡器上同时有10个座,可以同时放10个记录器,读卡器怎样才能识别到当前卡座上放的是哪个记录器?有没有什么电路能近距离发射能量(比如垂直方向3CM以内),能量传输到对应的读卡座上的记录器,使得MSP430的某个管脚能读到高电平。这样就能知道哪个卡座上放着记录器了,也不会误认到相邻卡座上的记录器。电路
    helloxieyu 微控制器 MCU
    对SD卡的读写程序
    求各位大神帮忙,我想写一个关于把对声音采集来的数据用msp430单片机存到SD卡然后在读出来的程序,请各位帮帮忙!!!先谢谢拉!!
    顽皮小孩 电子竞赛

    推荐内容

    可能感兴趣器件

    EEWorld订阅号

    EEWorld服务号

    汽车开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2023 EEWORLD.com.cn, Inc. All rights reserved