• 本课程为精品课,您可以登录eeworld继续观看:
  • RECEPTACLES INSTALLED IN BATHROOMS OF COMMERCIAL AND INDUSTRIAL LOCATIONS - 210.8(B)(1)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    MSP-FET430UIF连接电脑无任何反应 并且两个灯都不亮
    [i=s] 本帖最后由 testingphone 于 2016-1-21 14:52 编辑 [/i]MSP-FET430UIF 连接电脑后,电脑”设备管理器“里端口没有任何反应,并且两个指示灯都不亮!有谁懂维修的指点下!我现在测8M,12M 晶振都是有波形的,左上角有3.6V 供电的。朋友说供电有问题,但不知道具体哪些是关键测试点!连接电脑USB后,变砖的仿真器会有提示吗?[img]https:/
    testingphone 微控制器 MCU
    乘法器分析
    我是用AD835做混频,将两个相位不同的正弦信号混频,然后滤波,理论上滤波滤除的直流是与相位有关的一个直流量,在输入信号幅度稳定的条件下,但是我得到的直流分量不仅和相位差有关系,和频率也有关系,也就是咋改变频率的时候,得到的结果不是稳定的,有没有哪位大神可以帮忙解决这个问题啊,或者可以有一款直流偏置不会随着频率变化而变化的乘法器推荐,跪求结果
    fowerboy 模拟电子
    【平头哥RVB2601创意应用开发】开发板bring up,点亮LED
    1. 继上周开箱后,这周开发板bring-up,遇到了一些问题,跟大家分享下。2. 其实在收到板子前,我已经下载了CDK软件和CH2601_SDK例程,一拿到板子我就跑通了helloworld例程,当时还想着怎么这么顺利,因为交流群里很多人遇到了CDK各种Bug。3. CDK我用的剑池CDK集成开发环境V2.12.1,CP210X 串口驱动电脑本来就有,所以开发环境的配置还是很顺利的。https:
    dragon2610 玄铁RISC-V活动专区
    国外网友给STM32F4Disco做的扩展板
    [url=http://forum.micropython.org/viewtopic.php?t=2089&p=11816]Display/Expansion shield for STM32F4Disco[/url]可以连接外部RGB显示器,玩俄罗斯方块。
    dcexpert MicroPython开源版块
    求《windows2000驱动程序设计指南》源码
    麻烦给个链接或将资料发至:Win32Fan@yahoo.com.cn 多谢!
    gueichun 嵌入式系统
    (转载)如何解决AD5930输出有时钟产生的谐波问题
    [i=s] 本帖最后由 天明 于 2014-6-30 11:23 编辑 [/i]最近我在设置一个DDS信号源的时候,为了输出三角波选用了AD5930,有源晶振选用的是40MHZ,但是在输出时发现三角波上叠加了一个80MHz的正弦波(幅度大约30mV),这个应该是时钟的问题,但是在我对晶振添加了一个低通的LC滤波器(截止频率60MHZ),发现80MHZ的没了但是出现了一个40MHZ的而且幅度更大了。
    天明 ADI 工业技术

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved