• 本课程为精品课,您可以登录eeworld继续观看:
  • LIGHTING OUTLETS IN ATTICS - 210.70(C)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    我们上学期老师叫我们做的51最小系统PCB+原理图。
    最小系统。呵呵
    谢谢分享 51单片机
    STM32F103ZET6的TIM5-TIM8不能工作(新手求助)
    STM32F103ZET6的TIM5-TIM8不能工作,TIM1-TIM4工作正常。TIM2-TIM5是通用定时器,但是TIM5与TIM2\3\4配置完全一样,却不能工作。TIM1换成TIM8也是同样问题,查看寄存器,TIM5\6\7\8->CNT根本没有计数。下面是TIM2和TIM8的配置。static void TIM2_GPIO_Config(void){GPIO_InitTypeDef G
    舒影寒携 stm32/stm8
    三电平和两电平SVPWM的问题
    三电平和两电平SVPWM逆变器或者变频器的软件,是不是只有SVPWM发波部分不一样,其他部分可以通用?
    kata DSP 与 ARM 处理器
    导入motorware中的项目编译失败,请教解决方法?
    导入motorware中的项目编译失败,请教解决方法?环境ccs6.1.2如果按照默认不指定芯片具体型号,可以编译通过,但无法调试。指定了具体的芯片型号,编译时出现如上错误,错误信息error #16008-D: file"C:/ti/motorware/motorware_1_01_00_13/sw/modules/fast/lib/32b/f28x/f2806x/2806xRevB_FastS
    narong 微控制器 MCU
    【ST电机评测】任务三与自拟任务(PID整定与负载测试)
    [i=s] 本帖最后由 gyp1 于 2018-6-11 17:26 编辑 [/i][align=left][font=微软雅黑][size=4]接上贴(参见[url=https://bbs.eeworld.com.cn/thread-647187-1-1.html]【ST电机评测】测评前期准备(软件配置)[/url] )[/size][/font][/align][align=left][fon
    gyp1 stm32/stm8
    MSP430F6736的RTC_C模块无法写入啊!
    本人在用F6736做一款电表,遇到一个问题,就是RTC_C的模块的寄存器无法写入,我已经写入了0xa5h了,同样受到保护的RTCCTL寄存器都可以写入了,但是年月日的寄存器仍然不能写入,大家帮忙啊!!!!跪谢!!!
    qdavid64 微控制器 MCU

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved