• 本课程为精品课,您可以登录eeworld继续观看:
  • DERATING DUE TO OBSTRUCTIONS - 311.60(C)(2)(a) TO TABLES 311.60(C)(77) THRU 311.60(C)(86)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    关于DVI_D接口
    关于DVI_D接口 我现在有8路DVI信号(DVI_CK+,DVI_CK+,DVI_D0+,DVI_D0-,DVI_D1+,DVI_D1-,DVI_D2+,DVI_D2-) 但是DVI接口却有24路信号,这8路信号能否在显示器上产生图形,若需要产生信号,还需要哪几路?(比如电源或地?)谢谢各位好心人了~~
    frankay FPGA/CPLD
    个人穿衣指数提示
    1.放置到个人窗户外,早上闹铃响起就连接手机发送此时监测到的天气温度,湿度等信息到手机,从而帮助主人决定穿衣类型及厚度。还有利用[color=#525252][font=Arial, sans-serif][size=12px]SensorTag的可用一切功能做个超级个人助理吧。还有什么功能,需要研究一下。。。[/size][/font][/color]
    a252284222 无线连接
    关于配置文件中的若干符号的问题
    在XXX.bat,XXX.reg和source文件中经常会遇见;,@,#这三种符号。;应该是注释掉的意思。@应该怎么理解?比如:set BSP_NOUSBFN=set BSP_USBFNCLASS=SERIAL@REM set BSP_USBFNCLASS=MASS_STORAGE#又该如何理解?(这里的#并不是#define定义的#)比如:#$(_TARGETPLATROOT)\lib\$(_C
    可乐虎 嵌入式系统
    基于3U PXIe 的ZU11EG的通用主控板
    基于3U PXIe 的ZU11EG的通用主控板1、板卡简介基于3U PXIe的ZU11EG/ZU7EG/ZU7EV的通用 ,实现FMC的数据接口和主控计算,广泛应用于工业控制,检测,视觉处理。支持工业级温度工作。2 主要功能1 板卡核心芯片使用ZU11EG-2FFVC1156I MPSOC处理器,PL端一路DDR4 64bit,PS端一路DDR4 64bit,支持EMMC、QSPI Flash、
    VCC135 FPGA/CPLD
    关于STM8的中断问题
    在STVD建立工程后,有一个stm8_interrupt_vector.c的文件,我在里面建立了中断向量和中断服务函数,但是问题来了,在main函数中怎么使能中断和关中断啊?还是已经是默认启动了?我以前做过飞思卡尔的,建立完工程,就有个使能中断的头文件hide.h,可以用里面的宏使能和关中断。求大虾指教。。。。。。小弟感谢不尽
    忧乐游子 stm32/stm8
    网络开发笔记9_Access数据库基础
    一 为什么学Access为什么学Access? 很多朋友要奇怪的问了,你不是在讲Lm3sxxxx的网络开发吗?咋个讲起Access数据库来了,这不是牛头不对马嘴,挂羊头买狗肉了吗?不,一点也不,首先既然你也是在学习,那么多学一点对你并不会坏的。或许现在你用不着,将来的某一天或许你就用得上这样的方案了呢?其次,我们之前做了一个数据的采集实验,数据的处理就不用我多说了,不同的系统对数据的处理是不一样的
    yuhua8688 微控制器 MCU

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved