• 本课程为精品课,您可以登录eeworld继续观看:
  • RECEPTACLES INSTALLED ON ROOFTOPS OF COMMERCIAL AND INDUSTRIAL BUILDINGS - 210.8(B)(3)​​​​​​​
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    用户评论

    暂时无评论

    猜您喜欢

    推荐帖子

    *** WARNING L13: RECURSIVE CALL TO SEGMENT
    #include "reg52.h"#include//包含atof(),字符串->实数#include//包含sprintf(),实数->字符串#include//包含strcpy(),字符串复制#include//数学函数头文件#define uchar unsigned char#define uint unsigned intsbit choose=P3^4;//时钟和计算器选择键/***
    wengxiaomin 51单片机
    关于F28035 AD转换结果(ADCRESULTx)问题请教
    [align=left][color=#000]有个关于F28035 AD转换后结果存储的问题想请教,问题如下:[/color][/align][align=left][color=#000]1.连续或单次AD采样后的结果是如何存储在寄存器ADCRESULTx中的?[/color][/align][align=left][color=#000]比如SOC0~ADCRESULT0...SOC15~A
    Liuliming 微控制器 MCU
    求助!由一位I/O口控制两个LED的四种状态?!
    由一位I/O口控制两个LED的四种状态:分别为两LED同时亮,同时不亮,一亮一不亮,闪烁!!
    qing930 模拟电子
    Atmega16的常量无法读取
    [i=s] 本帖最后由 ltwsq 于 2015-4-17 13:33 编辑 [/i]用CVAVR编写了一段程序,其中定义了一个常量数组。flash unsigned int level_count[]={0x0000,0x0001,0x0001,0x0001,0x0001,0x0001,0x0001,0x0001,0x0001,0x0001,0x0001,0x0001,0x0001,0x0001
    ltwsq Microchip MCU
    PCB设计规范
    PCB的设计规范,很好用的。
    邱宇sky PCB设计
    想用STM32+NAND128做大容量存储
    想在英蓓特EM-STM3210E的开发板上用STM32+NAND128+SD卡做大容量存储,但用官方的例程只能对SD卡操作,对NAND不行,总是提示要格式化,但格式化不成功。NAND和SD卡用的同样的USB程序,只是根据不CBW命令中不同的逻辑块来选择memory是SD还是NAND,能操作SD说明USB程序应该是没问题的,那为什么操作NAND不行。NAND128单独用程序测试过,读写扇区正常。用B
    diablozyr stm32/stm8

    推荐内容

    热门视频更多

    可能感兴趣器件

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved