课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    BUG-5438多个中断
    需要用5438产生一个64khz的方波,还要以8khz的频率采集电压,AD用的是内部自带的,同时每隔1m采集一次温度,在使用中断的时候,主函数里开启全局中断,但是定时器中断里要是不再打开中断的话,会只有定时器中断工作。但是要是定时器中断里使能全局中断,AD转换可以工作,但是方波频率就不对了。解决办法:AD转换不使用中断,改用在定时器中断里隔7次启动一次AD转换。中断的这段时间里,足够AD转换完成。
    平行电 微控制器 MCU
    Ti DSP 优化基本策略
    [size=4]一、优化流程一般分为三个阶段。[/size][size=4][/size][size=4]阶段一:直接按照需要用C语言实现功能。在实际的DSP应用中,许多算法直接用汇编代码编写,虽然优化效率很高,可是实现的难度却很大,所以一般先用C语言来实现,然后编译运行,利用C64X开发环境的profile; clock工具测试程序运行时间,若不能满足要求,则进行第二阶段。[/size][siz
    fish001 DSP 与 ARM 处理器
    电流源
    [i=s] 本帖最后由 paulhyde 于 2014-9-15 08:52 编辑 [/i]我设计了一个电流源。但是只能输出200毫安以下的电流。我想要大电流,怎么办?
    gonghuomu 电子竞赛
    电感设计软件
    电感设计软件,从别处下载的.
    jinpost 无线连接
    怎么设置IP呀 ?
    我是菜鸟, 我想知道怎么在WinCE里面设置IP. 察了半天都说修改注册表. 可我连注册表都打不开呀. 我是用 VS2003做得开发.我想在程序里面进行修改. 高手能否提供一个修改注册表得函数, 或者API之类得, 感激不尽啊!!!!
    marchz 嵌入式系统
    高分! 在51里的串口接收中如何加入超时处理?
    我现在需要用到2051接收来自PC的数据(长度不定,但长度信息是在接收的第一个字节里),打算用方式1,定时器2,串口超时了就表示接收已经完成,现在问题是:如何实现串口的超时处理? 是用另外一个定时器?还是在等待RI的过程中DJNZ某数以实现计时?请指教
    请求权 嵌入式系统

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved