• 本课程为精品课,您可以登录eeworld继续观看:
  • PROTECTION IN GARAGES - 210.8(A)(2)​​​​​​​
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    南京工信部认证企业【高薪急聘IC工程师】
    [align=left][font=宋体]目前公司开放的全职岗位如下,学历要求专科及以上。欢迎有意向的同学[/font][font=宋体]将简历及成绩单发至邮箱[/font]hr@chiptel.com.cn[font=宋体],[/font][font=宋体]谢谢。[/font][/align][align=left] [/align][align=left]1.[font=宋体]模拟[/font
    Chiptel 求职招聘
    CCS 6新建TMS320F2812工程
    准备材料CCS6下载地址:http://www.ti.com/tool/ccstudioF2812的C语言头文件下载地址:http://www.ti.com/lit/zip/sprc097安装后的文件结构样式如下:新建空的工程点击Project-New CCS Project。在New CCS Project窗口中,按需要填写以下内容后按Finish完成新建空的工程。新建完成后的工程,结构如下:点
    fish001 微控制器 MCU
    uc1701
    有哪位大侠用过uc1701x控制器的LCD点阵液晶屏丫怎么弄都不亮 :surrender:
    xiha FPGA/CPLD
    关于API绘制控件
    复杂控件如:progressbar等如果不做处理,其显示效果是系统自己绘制(灰色的底色,蓝色的进度),现在项目要求按美工设计的效果自己用API绘制,不知道该怎么解决,上网查了很多资料均只是谈到用法,而很少涉及绘制。请各位大侠帮忙,提示一下
    bayasina 嵌入式系统
    晒设计方案+马里奥大叔--听我指挥【实战】
    [i=s] 本帖最后由 sjtitr 于 2014-2-20 00:51 编辑 [/i]依然,首先回顾构想贴:[url=https://bbs.eeworld.com.cn/thread-429514-1-1.html]晒设计方案+马里奥大叔--听我指挥[/url]本辑内容,核心内容是讲述如何使用鸡腿,以及少量的I2C的使用。到此为止,算是实现了NES模拟器的基本目标。不能玩的游戏机那还算不上游戏
    sjtitr stm32/stm8
    EXTI9_5中断为什么一直不停?
    使用STM32F103,用它的GPIOE2、3、4、5、6五个口作为键盘输入,初始化这的程序为:/* Configure EXTI line */EXTI->EMR = 0x7C;//line 2,3,4,5,6 的中断MASK位EXTI->IMR = 0x7C;//事件MASKEXTI->RTSR = 0x7C;// 上升沿触发EXTI->FTSR = 0x7C;// 下降沿触发EXTI->PR
    dontium stm32/stm8

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved