• 本课程为精品课,您可以登录eeworld继续观看:
  • (a) ADDITIONAL REQUIREMENTS FOR FEEDERS - 240.101(A) AND (B)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    【招聘】本单位诚聘DaVinCi等各类讲师
    本单位招DaVinCi等各类讲师,要求有一定项目经历,表达能力强,待遇高,可周末,有意者请与我联系。地点北京,上海等地,QQ:1489302364,邮件:hailang869@163.com,联系人:罗先生
    sicengmei 求职招聘
    I奇怪的O口配置现象!!!
    我想配置P1.0——P1.3为输入,P1.4——P1.7为输出,程序如下P1DIR = 0xf0;P1OUT = 0xff;然后我用万用表测量了一下,发现P1.0和P1.3为低电平,这是为什么啊?用什么方法可以把P1.0——P1.3配置为输入,并且用万用表测量的时候为高电平啊!!!大家有什么方法吗?
    wuqingyou 微控制器 MCU
    WinCE6.0的安装问题
    今天又安装WinCE6.0,安装还是不成功,机器是为了安装它才又将整个系统重装的。情况是这样的:1、安装VS5,及SP12、安装WinCE6.0及SP1现在安装后,在开始菜单里只有“Release Notes ”及“test kit”两项,没有发现PB在哪儿。注,我过去曾安装过WinCE5.0,并且只安装它,没有安装VS,一下子就成功了,我想可能是我安装过VC++6.0 的原因吧,可是我后来在系统
    belongto 嵌入式系统
    程序不运行
    我的板子上连接外接控制部件,传感器,430就不运行,但是如果除了外接电源,其他都拔除,则430开始运行,然后可以把外接控制线,及传感器等线连接上,430仍继续运行.什么原因
    zdh09 微控制器 MCU
    lpc175x超频
    [b]stm32超频已经被各位网友开发的到濒临极限了。但是lpc175x超频很少有人用呀,在GOOGLE上搜索一下,stm32满满几页链接,LPC17XX没有几个有用的链接。我现在的产品LPC1754运行在12x11=132Mhz,首批小批量100块,发下去让客户试用,结果有客户反映,串口不稳定,我思考了一下:超频后产品中运行的程序与没有超频的产品是一样的程序,唯一不同的是超频后的新产品我在串口的
    zhaojun_xf NXP MCU
    谁有没有办法把LAUNCHXL-CC2640R2的swrc335转成Altium Designer Winter 09版本
    谁有没有办法把LAUNCHXL-CC2640R2的swrc335转成Altium Designer Winter 09版本
    蓝雨夜 无线连接

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved