• 本课程为精品课,您可以登录eeworld继续观看:
  • LIGHTING OUTLETS IN STAIRWAYS - 210.70(A)(2)(1)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    哪位高人知道,在Windows Mobile 6.0 SDK环境下,如何用DirectShow 和 DirectDraw 使用overl
    哪位高人知道,在WindowsMobile6.0SDK环境下,如何用DirectShow和DirectDraw使用overlay2开发camera应用程序。谢谢了。
    wide 嵌入式系统
    LWIP协议栈参数配置
    请教大家了,在ZLG的8962开发板上分别运行了2个UCOSII+LWIP例程,一个是基于LWIP API,一个是基于LWIP RAW.这两种运行方式应该是不一样的,可是我对比了这两种运行方式下的Lwipopts.h文件和opt.h文件,发现它们的参数配置都一样的,照说应该有区别吧?那他们的区别在哪里呢?
    ZHANGXUEJIE 微控制器 MCU
    收一个Pocket-RIO
    之前见有朋友出过一块,但是没抢到。作为labvIEW爱好者,想亲身体验下[color=#4298ba]FPGA[/color]在labvIEW的编程,望有意出售者联系
    suoma 聊聊、笑笑、闹闹
    Altium designer如何将PCB里的一个2D线框设置为丝印层?
    如图,是Altium designer 16的PCB截图,请问如何一次性将PCB内这一部分的2D线设置为丝印层?而不是一段一段的设置。发现即便选中一整圈,右键属性设置为overlay之后,也只设置了一段,还得一段一段选。
    elec32156 PCB设计
    电源EMI滤波器
    1 概述在电子设备供电电源上,存在有各种各样的外来干扰信号。很多电子设备本身,在完成其功能同时,也产生了形形色色的EMI信号,以及人为和大自然的EMI信号。这些EMI信号,通过传导和辐射的方式,影响着该环境里运行的电子设备。如图1.0是用示波器在220V/50Hz供电线上观测到的随机EMI信号。这就是EMI信号;电源EMI电磁干扰(美)IBM公司的一项研究表明:一台普通计算机装置每月都会遭受120
    czf0408 LED专区
    改板后得优龙开发板跑wince得一些问题:再开一贴
    [size=14px]运行优龙bootloader选择boot wince后bootloader加载wince结束后wince开始运行,但是到给flash挂载文件系统得时候就出错,直接崩溃了,原因是flash改成了1G的flash,BSP中flash驱动是支持1G得,挂载文件系统失败原因估计是参数配置出错(实在惭愧我找不到配置参数得地方,flash大小变了分区肯定要变),我没有修改配置参数,而wi
    haohaohao123456 嵌入式系统

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved