• 本课程为精品课,您可以登录eeworld继续观看:
  • PROTECTION OVER COUNTERTOPS210.8(A)(6) AND (A)(7)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    私藏资料大公开——数字设计原理与实践
    私藏资料大公开——数字设计原理与实践,跟大家一起分享
    swx9588 DIY/开源硬件专区
    [求助] 求助 fft.lib 做的IFFT变换的程序
    最近搞的很头疼怎么用DSP的fft.lib 这个库做IFFT变换呢??有没有高手用过呢? 跪求答案啊。。。只能做FFT变换的话没什么意义。。void IFFT(){int16 temp;fft.ipcbptr = ipcb;// FFT computation bufferfft.magptr= mag;// Store mag. square in separate bufffft.winptr
    陈奕圳 DSP 与 ARM 处理器
    电池持续时间太短(5)——我们担心什么?
    [b][u][size=16px][color=#033660]谬误之四:电池持续时间太短[/color][/size][/u][/b][size=16px]真正的无线设备无需为通讯或者电源铺设线路。但是传感器和无线信号总是需要电源的,所以电池便成为了最常见的电力来源。[/size][size=16px]电池需要定期更换,这没错――但是不像过去那么频繁,也不像您所想象的那么经常。典型的情况下,电池
    小瑞 无线连接
    AD5933的直流偏置和量程自动切换问题
    最近在使用STM32+AD5933设计阻抗测量系统,不考虑AD5933输出阻抗和直流分量对阻抗测量带来的影响,按照AD5933datasheet上的简单电路将AD5933和STM32单片机进行了连接,有关于AD5933和STM32的I2C通信、AD5933实部、虚部数据的读取、幅度的计算以及系统相位的读取的基本程序已经调试完成。这是今天做的一组实验,发现阻抗测量的误差还是挺大的。我用拨码开关控制反
    qiwan stm32/stm8
    读Flash启动失败
    我想问大家一个问题就是我在把microblaze 下载到prom中然后 写好一个Flash的lodar 想把应用程序写到FLASH中,可上电后读不出FLAH的东西?
    daicheng FPGA/CPLD

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved