• 本课程为精品课,您可以登录eeworld继续观看:
  • LONG- AND SHORT-TIME RATINGS OF CONDUCTORS - 310.14(A)(3) AND TABLE 310.16
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    怎么都是要电子种 小弟求个电子秒表的设计
    求电子秒表的设计希望GGJJ门帮忙 有了能发到我的邮箱里 谢谢了Email:wisslove@163.com
    wissl 单片机
    关于MSP430F5438A升级失败
    项目过程遇到一个棘手问题:升级成功后,再次升级时,快升级结束时(APP程序一共123包,每次都是死在120、121包)程序跑飞。经过单步跟踪,发现跑到0x0000,然后往下执行到0x0004,进入死循环。想到在MSP430F5438A无线升级中遇到的同样问题,开始找中断的原因。找了一遍,发现所有中断都写了中断服务程序,并且对APP中的中断都做了重映射。然后通过打断点运行,发现问题跟断点位置也有关系
    火辣西米秀 微控制器 MCU
    昨日狂风大作大雨倾盆,今日也无风雨也无晴
    三台共舞,小伙伴们你们那儿感受到台风的威力了吗?? 管管位置在福州这片,最近几年天气无常,从原先一个一年雨不停的地儿,连着闹了好几年旱灾,一年到头下不了几场雨,台风也连着几年对我们绕道而行了。今年好像情况缓解了,雨又回来了,连带着台风也光顾了。。这不,昨天狂风大作大雨倾盆,整个区从幼儿园到高中,全面停课了。到昨天晚上睡前还是大风呼啸,我还在想着,不知道今天是不是还要持续一天,我家小姑子晚上挺晚了还
    okhxyyo 聊聊、笑笑、闹闹
    求助,关于7005和7026
    之前一直在用 s3c2410+vivi+kernel2.4+ch7005ch7005的驱动是在vivi下,通过i2c往某地址写入特定的值来实现vga输出的,这些值和地址在ch7005的datasheet上都有详细说明在我这板子我是这样做的:#define VGA_ADDR 0xEA__Wr24C080(VGA_ADDR, 0x0, 0x60);__Wr24C080(VGA_ADDR, 0x4, 0
    xuan0912 嵌入式系统
    请高手指点霍尔元件
    :) 请各位高手指点:直流无刷电机能做绝缘强度(500伏兆欧表测量)检查吗?里面的霍尔元件能承受吗?
    why111122 模拟电子
    大疆华为等FPGA笔试面试视频解答
    [font=Verdana, Helvetica, Arial, sans-serif][size=14px]FPGA历届面试题解答视频,希望对大家有用[/size][/font][font=Verdana, Helvetica, Arial, sans-serif][size=14px][/size][/font][font=Verdana, Helvetica, Arial, sans-ser
    njiggih FPGA/CPLD

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved