• 本课程为精品课,您可以登录eeworld继续观看:
  • PROTECTION OVER COUNTERTOPS - 210.8(A)(6) AND (A)(7)​​​​​​​
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    git 使用方法学习
    以前也只是用svn,现在转到Android,怎么能不用高大上的git 呢?来吧,一起来玩转git 吧。1、git 安装sudo apt-get install git[color=#666666]就可以直接完成Git的安装,非常简单[/color][p=20, null, left][color=rgb(102, 102, 102)]安装完成后,还需要最后一步设置,在命令行输入:[/color][
    Wince.Android 嵌入式系统
    为什么调用不了modelsim?
    我装了quartus web10.1版,modelsim 6.5。。但是在调用modelsim6.5的时候不启动啊,win7系统,环境变量,路径什么的都设置了,同样的设置XP下就启动了。。。在点了eda rtl simulation 后下边也不提示错误,下边提示两条:1:Info: Successfully launched NativeLink simulation (quartus_sh -t
    wangpiaoke FPGA/CPLD
    使用高效MicroSiP电源模块助力超声波智能探头小型化设计
    近年来,随着居民健康意识的提高,超声检测的需求越来越多。在传统的超声检测场景下,待检者须在医院超声机台边排队等候。如果出现了待检者难以抵达医院或者超声机台资源紧张的情况,如何完成对待检者的检测就成了一个难以解决的痛点。超声波智能探头的出现,重新构建了新的超声检测场景。超声波智能探头的体积通常来说仅有手掌大小,医生可直接携带智能探头去待检者的场景下进行检测,大大提高了超声检测设备在应用中的灵活性。在
    alan000345 模拟与混合信号
    智能无线充电管理系统
    [i=s] 本帖最后由 JaneConan 于 2018-9-23 22:38 编辑 [/i][font=宋体][size=17px]首先非常感谢电子工程世界和兆易创新组织的活动,[/size][/font][font=宋体][size=17px]智能无线充电管理系统是借学校大创活动的东风,与实验室小伙伴儿们一起学习和研究更多控制系统而发起的。[/size][/font][font=宋体]本项目研
    JaneConan GD32 MCU
    速来:11.11元购万用表、开发板啦,属于e络盟新用户的双11盛宴~
    活动已结束~获奖名单:点此查看第一轮获奖名单点此查看第二轮获奖名单点此查看最后1轮获奖名单一年一度的双11来了,各种套路横出,我们,只想简单点。一起来看看e络盟商城的双11福利。福利一:新用户无门槛85折,满200元即可顺丰免邮,点此进入商场福利二:新用户,11.11元秒杀购买场我们认真地为奋斗在一线的电子工程师,准备了一份惊喜11.11元购清单:有万用表、无线开发板、焊台、电机驱动板好货且便宜,
    nmg 综合技术交流
    15通道锂电池管理模块
    [color=#000][font=Arial, Helvetica, sans-serif][size=12px]48V及以下电压的锂电池单元在微混动汽车和工业储能中的应用率很高。系统由13至15个锂电池单体构成。由于锂电池固有特性,需要对该数量的电池单体进行精确监测,以保障系统安全性并提高电池效率和寿命。[/size][/font][/color][color=#000][font=Arial
    dontium 能源基础设施

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved