• 本课程为精品课,您可以登录eeworld继续观看:
  • LUMINAIRES OVER SPAS OR HOT TUBS - 680.43(B)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    STC开整M0内核单片机了
    前阵和论坛工程师聊国芯,聊到了M0到期开源今天,不小心撩了下STC家,没啥原因,纯粹的见到老友,激动了一下下。然后就开启八卦模式:
    nmg 国产芯片交流
    基于STM32和ESP8266的低成本物联网控制盒子
    [i=s] 本帖最后由 汤权 于 2016-11-30 10:18 编辑 [/i]我之前发过一个帖子:[url=https://bbs.eeworld.com.cn/thread-496527-1-1.html]https://bbs.eeworld.com.cn/thread-496527-1-1.html[/url],这是关于搭建一个简单的智能家居系统。现在我把这个小智能家居系统给做了个小盒子
    汤权 stm32/stm8
    为什么用直联线也可以通呢?
    我们开发的嵌入式设备两台间用直连线和交叉线都可以通,谁知道原因呢?我用的是Realtelk的8201网卡芯片?
    zhengkuo 嵌入式系统
    8寸屏的问题
    我公司要做一个项目,需要用8寸触摸屏。准备买一个8寸屏,问卖家技术支持,说是STM32带不动那么高分辨率的屏。只有ARM或者FPGA才可以带动。那是不是必须用ARM或者FPGA啊?谢谢!如果是那样,我就得现学ARM或者FPGA。
    chenbingjy stm32/stm8
    MSP430的时钟问题
    单片机上电后,如果不对时钟系统进行设置,默认800 kHz的DCOCLK为MCLK和SMCLK的时钟源,LFXTl接32768 Hz晶体,工作在低频模式(XTS=O)作为ACLK的时钟源。CPU的指令周期由MCLK决定,所以默认的指令周期就是1/800 kHz=1.25s。要得到ls的指令周期需要调整DCO频率,即MCLK=1 MHz,只需进行如下设置:BCSCTLl=XT20FF+RSEL2;/
    fish001 微控制器 MCU
    1602液晶51单片机程序向msp430g2553移植出现问题
    [i=s] 本帖最后由 追梦人weijian 于 2014-8-10 11:24 编辑 [/i]写入数据函数和写入命令函数中DataPort=com;编译不通过,程序为/*-----------------------------------------------名称:LCD1602论坛:[url=http://www.doflye.net]www.doflye.net[/url]编写:shif
    追梦人weijian 微控制器 MCU

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved