• 本课程为精品课,您可以登录eeworld继续观看:
  • (a) APPLYING BOTH DERATING FACTORS TABLE 310.15(C)(1) AND TABLES 310.15(B)(1) AND (B)(2)​​​​​​
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    Protel 99从入门到精通教程(上)
    送给大家一本比较完美的99教程中册:https://bbs.eeworld.com.cn/thread-52306-1-4.html下册:https://bbs.eeworld.com.cn/thread-52318-1-8.html
    天道自然 PCB设计
    各种复位IC的介绍及复位电路的设计(周工强悍资料)
    对于单片机系统来说,复位电路应该是最为最要的一个环节。往往被很多人忽略,因为一般简单的复位电路在开发试验阶段是没有问题的,只有在工作环境中才容易出现问题。所以在此推荐这份资料希望大家重视,复位IC并不会增加太多成本,但是更有保障。[[i] 本帖最后由 zhaojun_xf 于 2010-7-12 09:30 编辑 [/i]]
    zhaojun_xf 单片机
    程序烧入FLASH 复位不能运行的问题?
    [i=s] 本帖最后由 dontium 于 2015-1-23 13:31 编辑 [/i]看看论坛,好象很多战友都遇到了这个问题,不知道大家是怎么解决的,我遇到的问题是这样的,我用汇编编写了一个小程序,小于1K,作用是把GPIO拉高,在调试时候运行正确,烧入FLASH中的数据,对应于调试时调入RAM中的数据完全一致,说明烧写入FLASH成功了,用FLASH加载的引脚,配置的寄存器经检查也没有问题,
    sapt 模拟与混合信号
    光电二极管阵列参数计算
    这是芯片的主要参数我们要用到的是S4111-46Q从这些参数 怎么可以求出它的输出电流或者输出电压?求助谢谢
    司琦⑦ 模拟电子
    MSP430F149中12位ADC的最大电压测量值只有3.3V吗?
    我将参考电压设定为内部AVcc和AVSS时候,测定的值是准的,但是当我把参考电压设成VR+=VREF+(外接5v),VR-=AVss时,测GND的值读ADC12MEMx居然不是0,而是1000多,是否说明 12位ADC的最大电压测量值只有3.3V,如果不是,那为什么会测不准呢?一下是ADC的设定:void ADC_init(){ADC12CTL0 = SHT0_2 + ADC12ON;// Set
    myleshuzx 微控制器 MCU
    微波控制电路
    成功电路图!
    YUFEI7810 模拟电子

    推荐内容

    热门视频更多

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved