• 本课程为精品课,您可以登录eeworld继续观看:
  • SIZING - 210.20(A), 215.3, AND 230.42(A)(1)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    TMS320芯片的命名方法
    [size=4]TI DSP TMS320芯片的命名方法1.前缀:TMX=实验器件TMP=原型器件 TMS=合格器件2.系列号:320=TMS320系列3.引导加载选项:(B)4.工艺:C=COMSE=COMSEPROMF=FlashEEPROMLC=低电压CMOS(3.3V)LF=FlashEPROM(3.3V)VC=低电压CMOS(3V)5.器件类型:20x DSP24x DSP54x DSP
    Jacktang 微控制器 MCU
    TI--M4内部EEPROM详解
    M4里面的EEPROM并不是编址在内存空间中的,而是直接通过操作寄存器(Register)进行读写的。所以EEPROM中间的某个地址就是只属于EEPROM的地址,并不和内存地址有冲突。要想方便的使用EEPROM,最好的办法就是使用TI的StellarisWare驱动库程序:#include "inc/hw_memmap.h"#include "inc/hw_types.h"#include "in
    Jacktang 微控制器 MCU
    语音音频统一编解码算法研究
    最近在研究MPEG-D的USAC,不知道有没有朋友也在研究语音和音频统一编码算法,有的话不妨交流下
    lin郁风 淘e淘
    利用MEMS惯性感测技术实现应用变革
    [i=s] 本帖最后由 雨中 于 2014-9-27 22:09 编辑 [/i]虽然MEMS(微电子机械系统)技术被用于安全气囊和汽车压力传感器领域已有二十年左右,但却是任天堂Wii和苹果iPhone的热销使人们更广泛地了解惯性传感器的用途,这些产品使用了基于运动感测技术的用户界面。尽管如此,在一定程度上业界的观念仍停留在惯性传感器主
    雨中 ADI 工业技术
    关于USB管道名的问题 (八百里加急)
    小弟现在在开发上位机程序用到USB 通讯 ,但是驱动资料上只给除了两个管道名由于种种原因 这两个都不符合要求我该怎么样得到管道名 (用一个共享软件 人家都可以得到的)请高手指点!!
    darkgrass 嵌入式系统
    【GD32L233C-START测评】基于串行通讯的触摸屏控制LED
    [i=s] 本帖最后由 jinglixixi 于 2022-2-13 10:38 编辑 [/i]使用迪文智能屏的触摸操作可进行参数的设置,所设置的参数又有可以借助串行通讯来输出参数值。若接收该参数,则可以对外设加以控制。若接收该参数,则可以对外设加以控制。为此,这里设计了一个通过触摸操作来控制LED的功能,其电路连接如图1所示,也就是将智能屏的TX2和GND引脚分别同GD32L233开发板的RX和
    jinglixixi GD32 MCU

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved