• 本课程为精品课,您可以登录eeworld继续观看:
  • DEDICATED EQUIPMENT SPACE - 408.18(B) AND 110.26(E)(1)(a)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    请教GD32E230C的PB引脚问题
    [color=rgb(68, 68, 68)][backcolor=transparent][font=Tahoma,]我准备驱动RD117模块,这个模块是用I2C通讯的,原来准备用固件I2C,开发板上已经将I2C直接连接AT24C02了,不方便与RD117共用(虽然可以将AT24C02的引脚1断开,然后用跳线作片选信号,但RD117却没有可作片选控制的引脚)。我查找了相关的资料,确定用PB3、P
    hujj GD32 MCU
    CDMA通信网络
    利用CDMA通信网络传输视音频实现无线视频监控技术已经在多个城市成熟应用。由于CDMA信道属于公共网络,网络的带宽是有限制、不可控性,并且此类产品要实现本地、远程2路编码,对编码码率要求极高。在无线网络监控,带宽决定视频效果的一切。硬盘DVR原本基于标准的以太网应用,编码应用是符合固定网络带宽,在超低带宽时编码码率控制上一般最低控制在20kBps,而CDMA 1X瞬间网络经常性的从5 kBps至6
    jek9528 工业自动化与控制
    求助目前主流的汽车厂商使用CAN物理层协议都有哪些呀!!
    目前开始着手车载项目,需要了解现在主要的汽车厂商所使用CAN总线的物理层协议标准,求助!!谢谢啦:handshake
    浏阳河12407 汽车电子
    430单片机堆栈问题
    编译时出现这样的提示,是由什么造成的?又该如何解决?谢谢!screen.width-300) {this.width=screen.width-300;this.alt='点击查看全图';}" onmouseover="if(this.alt) this.style.cursor='hand';" onclick="if(this.alt) window.open('d:/10.jpg');" b
    dsx_msp430 微控制器 MCU
    消防设施的维护常识
    一、消防设施的种类:建筑消防设施归纳起来共有13类(一)建筑防火及安全疏散设施(二)消防给水(三)防烟、排烟设施(四)电气与通讯(五)自动喷水灭火系统(六)火灾自动报警系统(七)气体灭火系统(八)水喷雾灭火系统(九)低倍数泡沫灭火系统(十)高、中倍数泡沫灭火系统(十一)蒸汽灭火系统(十二)移动式灭火器材(十三)其他灭火系统二、消防设施的保养与维护1.室外消火栓由于处在室外,经常受到自然和人为的损害
    jek9528 工业自动化与控制

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved