• 本课程为精品课,您可以登录eeworld继续观看:
  • STANDARD AMPERE RATINGS - 240.6(A) AND TABLE 240.6(A)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    【为C2000做贡献】重量级资料:DSP教程-手把手教你
    此资料来源于网络是对于初学者绝对好的教程,如果想快速学习DSP,大家可以去网上搜《手把手学DSP》资料下载:详细内容如下:[[i] 本帖最后由 fxw451 于 2011-4-7 20:47 编辑 [/i]]
    fxw451 微控制器 MCU
    弱弱的问一问有没有用新唐的M451单片机的同学
    RT弱弱的问一问有没有用新唐的M451单片机的同学。有没有人正在移植LDC1000的程序。
    温文尔雅的饭饭 电子竞赛
    用LM2596时遇到的奇怪问题
    这几天我用LM2596-5.0输出-5V的电压,按照TI官网上的图焊好电路板之后,用万用表测了一下,好了!!!可是,第二天我再上电之后电源显示过载,本来设定的是12V的输入电压一下子被拉低到1.7V,我很奇怪,然后我尝试加大电流,但是电流大了之后非但过载问题没有解决,芯片还特别烫。把板子检查了好多遍后,我决定重新焊了,在这里我要说明一下,芯片是从TI申请的,应该不会是芯片问题。昨天重新焊好之后,还
    樊旭超 电源技术
    寻LED显示屏供应商(不知贴在这边合适不合适)
    有朋友最近想做LED广告屏,让帮忙找找有没有合适的供应商。有意向的可以留下联系方式和公司产品介绍相关链接,谢谢~
    houyb 嵌入式系统
    求助,遇到未解之谜
    最近在做LPC1768的IAP在线升级,目前已可通过ISP下载IAP bootloader程序到前64K,并可通过CAN口通讯,进行应用软件的下载到后面的空间。启动时从bootloader的main入口处就判断标志,选择运行下载程序还是应用程序。运行过程中,定时器、串口、CAN口、AD等等的中断都算能正常运行,但是有一个问题如下面这个帖子的兄弟提到的,基本一模一样,帖子貌似沉了好久,未解之谜,大家
    qzh7461102 NXP MCU
    TLP3547评测--设计应用对比
    我是最后一批的通过名单,收到这个模块的时候,已经在网上看到很多测试,也基本囊括这个模块的性能和特点,本来也就没有什么动力来滥竽充数。但模块也到手了,总的会有一些个人的看法,希望能给大家带来收获。说实在的,这个模块我觉得做出来的效果类似一个半成品的模组。就差没有塑封了。所以给人的感觉有点美中不足。因为这个想真真实实用来测试,毕竟做出测试勾的方式会比较好链接。好了,以上是题外话,具体的测试我没有深入去
    fsyicheng 东芝光电继电器TLP3547评测

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved