• 本课程为精品课,您可以登录eeworld继续观看:
  • SIZING - 210.20(A), 215.3, 230.42(A)(1), AND 230.90(A)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    【Atmel SAM R21创意大赛周计划】+Peer2Peer项目添加SERCOM (i2c)TWI
    【Atmel SAM R21创意大赛周计划】+Peer2Peer项目添加SERCOM (i2c)TWIR21的管脚不够多,只能考虑多用外设来扩展了!现在先从SERCOM (I2C)TWI功能开始,读取温度,硬件先考虑用at30片子!1、为sam0添加I2C外设sam0/drivers/i2c相关文件夹和文件大概可以步步新建添加2、添加目标芯片底层驱动common2 / compoents / se
    蓝雨夜 Microchip MCU
    CC3200 FreeRTOS软件定时器无法进入回调函数问题
    CC3200 FreeRTOS软件定时器无法进入回调函数问题,请问有人用过FreeRTOS的软件定时器吗?我的配置如下:/* Timer related defines. */#define configUSE_TIMERS1#define configTIMER_TASK_PRIORITY2#define configTIMER_QUEUE_LENGTH20#define configTIMER
    awarenessxie 无线连接
    xilinx ise 14.7 程序下载
    双击芯片添加bit文件时为什么秒退??
    499281736 FPGA/CPLD
    传感器经典资料
    嘉懿 传感器
    通过MSP430F149的串口对温度监控器进行配置
    通过MSP430F149的串口对温度监控器进行配置,对串口不了解,有哪位可以提供一下思路吗?温度监控器 用温度传感器DS18B20进行温度采集,12864LCD液晶显示屏显示温度,日期等
    qiao2012 微控制器 MCU
    晒晒TI的保温杯 ---很不错的
    收到的包裹:一个保温杯:
    dontium TI技术论坛

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved