• 本课程为精品课,您可以登录eeworld继续观看:
  • RECESSED LUMINAIRES - 410.115(B) AND Ex.'s 1 AND 2
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    【请问】1394异步写请求为何无响应?
    往1394接口的SONY摄像机里发一个4字节的写请求没有响应,但是读请求确有响应,而且还能返回要读的数据,我仔细检查了一下发送的数据包,应该没有什么错误,都是按协议来的,以前用Basler的摄像机都是好的,不知道为什么换了Sony的就不行了,请高手们指点一下。
    weison86620 嵌入式系统
    论坛能不能搞点户外运动工具的奖品?
    看那个小日本的奖品有一个Camppal一分钟自动速开帐篷,[color=#03399]维氏瑞士军刀,不能不说心里还是被动一下,哎,确实意志容易受影响呀。[/color]论坛以后能不能弄些或者向客户推荐一点这类奖品?
    wangfuchong 聊聊、笑笑、闹闹
    用Spartan-6片了做的板子,请大家先过过目吧(转)
    目前只有丝印图,先欣赏一下吧。不知坛里有没有做,给大家分享下[[i] 本帖最后由 gauson 于 2009-12-16 11:00 编辑 [/i]]
    gauson FPGA/CPLD
    为什么要用CPLD或FPGA?
    我现在想给DSP外扩一块AD芯片,采样率要求10M左右。看到网上好多人外扩AD的话一般都会用到FPGA或者CPLD。但是我想如果AD是并口的话,那数据口直接和DSP的数据口连接,然后其他的片选,时钟等连接到DSP的IO口不是直接就可以了吗?为什么看到网上好多人用CPLD和FPGA的。可能我的问题太水了,不过因为是新手,大家多包含。我在网上查了许多资料,也没有人说为什么要用CPLD或者FPGA的,也
    mrwoshishei FPGA/CPLD
    从摄像头开始——高级驾驶辅助系统解决方案系列介绍
    近年来,随着人们对驾驶安全水平需求的不断提高,高级驾驶辅助系统(ADAS)相关技术的不断成熟,伴随着ADAS市场高速发展,摄像头的需求也更加旺盛。其应用场景也是非常多的,主要是以下几个应用场景:倒车后视摄像头360环视摄像头前向摄像头电子后视镜或流媒体后视镜防疲劳驾驶DMS行程记录仪数字摄像头,主要有玻璃透镜、CMOS传感器、图像信号处理器(ISP)、电源管理、串行器、微处理器器等功能单元构成,如
    zqy1111 TI技术论坛
    利用单电源隔离放大器和ADC简化隔离电流和电压感应设计
    在保护人员、抗噪以及处理子系统之间的接地电位差等领域中,我们都需要一个它。你可以在以下应用中对它进行设计,如电机驱动器、太阳能逆变器、DC充电(桩)站、工业机器人、不间断电源、牵引逆变器、车载充电器和DC/DC转换器。我说的它指的就是电流隔离。包括我上述提及的系统在内,许多系统需要通过隔离势垒将电流和电压信息从一个电源域传输到另一个电源域,以便进行监视和控制。那么如何在隔离势垒上传输模拟信息呢?答
    alan000345 模拟与混合信号

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved