• 本课程为精品课,您可以登录eeworld继续观看:
  • ELECTRICAL SYSTEM COORDINATION - 240.12
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    用户评论

    暂时无评论

    猜您喜欢

    推荐帖子

    贴片元件的焊接标准是什么
    请教各位大侠,贴片元件的焊接标准是什么?
    绿茶 测试/测量
    DM9000c芯片外接三个网口需要几个芯片
    能不能给出三个网口DM9000c的电路图
    冰魄3009 模拟电子
    安世半导体&世平集团 Nexperia 在5G基础架构的应用 下载赢好礼!
    安世半导体世平集团 Nexperia 在5G基础架构的应用 下载赢好礼!活动开始啦~点击进入活动Nexperia 在5G基础架构的应用针对 Power 的关键在于功率效率和可靠性及相对高速传输速度与功率提升的需求,其中关键零件 MOSFET 扮演着提升效率和缩小体积的重要角色, Nexperia MOSFET 独步全球的 LFPAK 包装提供低阻抗高耐电流特性的解决方案。活动时间:即日起――202
    EEWORLD社区 无线连接
    电水壶自动断电控制器
    该装置的电路工作原理见图8。先在电水壶上用环氧树脂沾牢一只片状正温度系数的开关型热敏电阻RQ。将RQ的两端接到LSE的①、②脚,将水壶插入电源插座CZO中,揿下电源开关S,此时由于电水壶中的水温较低,RQ的阻值较小(<50K),故LSE的④脚输出高电平,继电器J立即吸合,常开触点j闭合,电水壶通电工作。松开手后,继电器J触点自保。一旦水沸腾(100℃),RQ的阻值阶跃上升,远大于50K,相当于LS
    程序天使 DIY/开源硬件专区
    关于r7f0c809单片机延时问题
    我想做一个led闪烁的程序,中间用for();去延时,发现该语句毫无作用啊。。刚开始还以为是我灯程序有问题,写了个按一下就亮不按就不亮的程序。可以成功跑起来。我就想问是不是不能用for();来做延时,一定要用定时器?
    a985227169 瑞萨电子MCU
    ADC软件校正求助
    小弟这两天在调一片别人做的ADC,测出来数据误差较大,因为没什么经验,也不知道用软件怎么校正比较合适。单端输入时,0-0.2V, 0-2.5V, 2.5V - 5V这几个电压范围进行多个点采样后拟合出来的点就不在一条直线上。双端输入结果更惨。真是无奈。{:1_134:}现在拟采用分段校正的方法。正在考虑要不是将零点校正和满量程校正加入,以便获取更精确的转换结果。还有温漂应该怎么校验呢,也是一头雾水
    lonerzf 模拟电子

    推荐内容

    热门视频更多

    可能感兴趣器件

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved