• 本课程为精品课,您可以登录eeworld继续观看:
  • RECEPTACLE OUTLETS FOR SMALL-APPLIANCE CIRCUITS210.52(B), 210.52(C), 210.11(C)(1), & 220.52(A)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    向李小龙学FPGA
    [align=left]还是从李小龙说起。伴随着一声“哟嚯”,飞出一脚后张开双臂身体半蹲的招牌式动作,被全球各地无数人模仿过。可是我们知道,全世界只有一个李小龙。无论你把“招式”模仿得多么惟妙惟肖,都无法达到那个效果。原因其实很简单,我们不具备他的速度和力量。采用反推法逆向思维,如果具备了他的速度与力量,任何一个招式都会威力无穷。由此可知,基本功是多么重要。[/align][align=left]
    guyu_1 FPGA/CPLD
    有人用过proteus仿真UART的人吗?--已解决
    [i=s] 本帖最后由 minjiang 于 2015-4-5 23:34 编辑 [/i]俺试过各种版本的软件,比如CCS6,Keil5.14和IAR7.0等编译得出的文件都不能在proteus的虚拟终端和虚拟串口+串口调试助手收到通过UART发送的数据,不过,这些例子在真实板卡上都能看到送出的数据,为什么?可能是雾霾造成的,今天天晴了,蓝天就出来了!!!
    minjiang 微控制器 MCU
    【转】说实话:模拟设计可以老但不可以朽
    安静的生活不需再起什么波澜,即将进入四十岁不再进入研发黄金时间段,想把自己做过的想过的都留下来,没有什么名利场的事情了,说出来格外轻松。面对目前大部分国内杂志近乎清一色的嵌入系统,单片机和软件的文章,硬件电路尤其是模拟电路设计似乎在很多人眼里过时了,只是怀旧情感而已,事实远不是这样,相信大家看看日本人怎么珍惜模拟设计的经验成果即可知道,再看看TI类似的公司09年的为何花大笔银子搞模拟,为何MAXI
    lixiaohai8211 模拟电子
    最近在做开关电源,给大家几份资料...逆变的,呵呵...可能不适合还望海涵
    最近在做开关电源,给大家几份资料...逆变的,呵呵...可能不适合还望海涵
    破茧佼龙 单片机
    ARM+LINUX 中断一定要用驱动在内核完成吗
    最近在折腾LINUX 的GPIO中断。用驱程实现了的情形是:1 在驱程里,借用copy_to_user函数,在中断发生时,让一个数值发生变化写回用户态,使得应用程序可以读出这个变化。问题是:这样看起来,好像跟查询没什么区别。以前玩51的时候,情况不是这样的,是程序跑着跑着,中断来了,就去执行。后来查资料,看了相关的书,觉得 异步通知机制 这个有点希望。可惜的是,不知道是不是参考的例程有哪里不对还是
    辛昕 Linux开发
    晒WEBENCH设计的过程+3.3VDSP供电
    [i=s] 本帖最后由 nwx8899 于 2014-8-17 13:22 编辑 [/i][size=9pt]利用易电源软件工具设计的一个[font=normal 宋体]DSP[/font][font=宋体]的一个供电系统,,输入电压是直流[/font][font=normal 宋体]14-22V[/font][font=宋体],输出[/font][font=normal 宋体]3.3V[/fon
    nwx8899 模拟与混合信号

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved