• 本课程为精品课,您可以登录eeworld继续观看:
  • (a) TAPS OVER 25 FT (7.5 m) LONG - 240.21(B)(4)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

用户评论

暂时无评论

猜您喜欢

推荐帖子

求问PSpice仿真电感参数设置
请问各位大神这句话是什么意思啊?为什么电感值有好几个?而且还用分号隔开了
Shirley_zh 电源技术
求救:fe425的ESP430模块可不可以测量不同频率电压信号的有效值?
好象在ESP430模块启动前要设置一个基准频率,比如说采集的电网频率为50Hz左右,那就设置为50hz,现在问题是我采样的频率在30-400Hz之间,咋办?另外就是esp430模块的中断频率是如何设置的?
starss 微控制器 MCU
防控警报响了
{:1_146:}管管家附近这里今天防空警报响了。也不知道是什么原因响的。有好长时间没听过这种警报声了。印象中还是读初高中的时候有段日子防空警报经常响起,当时台独呼声严重,我们跟台湾隔海相望,都说那边可能要打过来,还有部队官兵驻守在海边,每天操练还会经过我家门口。我们还进行了防空演习,学习听警报声采取措施。这个跟我今天的差不多。[audio]attach://232471.mp3[/audio]坛
okhxyyo 聊聊、笑笑、闹闹
最新版MSP430选型指南
每年的选型指南都是,MSP430新特性的总结,比如看看今年的:这是MSP430分离IO电压之后,设置了现在移动终端中更常用的1.8VIO电平,是希望将MSP430的应用扩展到移动设备中。
wstt 微控制器 MCU
图形化Linux开发工具TimeSys介绍
嵌入式Linux开发工具是一个开源的工具,全球各地的工程师都在更新它,所以导致他有很多不同的版本,TimeSys是一个图形化的开发工具,且是一个链式服务的开发工具,它可以及时为您提供更新服务,为您开发带来便利。双实与您携手共进嵌入式时代!
huxiao82 Linux开发
新手小白画的pcb板子求指教
大家好~上次发了一个自动布线版本的帖子,听从各位前辈意见改进之后现在是一个纯手工布线的版本,并且电阻电容大多改为了贴片电阻,封装都是1206.发现改为贴片电阻之后布线比之前有一个缺点,就是必须要加很多过孔才行。。。例如图中大概加了5个过孔。后来软件检查是警告说drill size,意思是过孔的大小问题?小弟在这里问一下过孔的大小应该怎么决定?线宽吗?另外图中V1V2VinVj以及+12V和GND这
度假的乞丐 PCB设计

可能感兴趣器件

完成课时学习+分/次

 
EEWorld订阅号

 
EEWorld服务号

 
汽车开发圈

 
机器人开发圈

About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

站点相关: 汽车电子 智能硬件

北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved