• 本课程为精品课,您可以登录eeworld继续观看:
  • PROTECTION IN BATHROOMS - 210.8(A)(1)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    使用ULINK 2 在线仿真AT91R4008 之仿真器安装
    使用ULINK2 仿真器在KEIL MDK 下在线调试AT91R40008。首先安装ULINK2 ,步骤如下:需要说明ULINK2 仿真器支持 各种ARM7 . ARM9 ,CORTEX-M,8051, 和C166 内核器件,可以代替以前老的ULINK仿真器言归正转,怎样安装ULINK 2 仿真器。 ULINK2 仿真器没有专门的驱动程序,直接使用WINDOWS XP 的USB驱动程序即可。1。
    eeleader 微控制器 MCU
    用VC编译驱动程序提示 "fatal error LNK1146: 没有用选项“/SECTION:”指定参数"该怎么解决?
    用VC编译驱动程序提示 "fatal error LNK1146: 没有用选项“/SECTION:”指定参数"该怎么解决?我是新手,谁能帮帮我,急啊
    mcd511786450 嵌入式系统
    怎样才能让电源寿命不受制于电容
    怎样才能让电源寿命不受制于电容在电路研发过程中,电容是最常用的电子元器件之一,主要用于平滑、储存能量或者交流电压整流后的滤波,另外还用于非精密的时序延时等。在代表电源寿命的 MTBF预计时,模型分析结果表明电容是影响开关电源寿命的主要因素,因此了解影响电容寿命的因素非常重要。影响电容寿命主要有以下几个因素:一是纹波电 流、二是等效串联电阻值、三是环境温度、四热点温度(电容内部温度最高点的温度)。电
    Fireflye 模拟与混合信号
    风吹麦成浪,蝉鸣夏始忙
    收获的喜悦,辛勤的汗水。
    btty038 聊聊、笑笑、闹闹
    中断问题(AT91 A3)高手求救!
    (灯)LED 与PA相连按钮(SW,一共四个按钮)与PB 相连#define LED_MASK(LED1|LED2|LED3|LED4)#define SW_MASK(SW1_MASK|SW2_MASK|SW3_MASK|SW4_MASK|SW5_MASK)高手帮我看看,为什么我按了SW4 ,没有反映呀(好像进不了中断呀)#include "Board.h"__ramfunc void aic_s
    liyanping 嵌入式系统
    求STM8S103F2/F3最小系统原理图
    谁手上有画好的STM8S103F2/F3最小系统原理图,借来一用,谢谢!
    suo618 stm32/stm8

    推荐内容

    热门视频更多

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved