• 本课程为精品课,您可以登录eeworld继续观看:
  • PROTECTION IN BASEMENTS AND CRAWL SPACES - 210.8(A)(4) AND 210.8(A)(5)​​​​​​​
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    全国大学生电子设计竞赛控制类题目对AD/DA芯片的要求。急!!!!!
    全国大学生电子设计竞赛控制类题目对AD/DA芯片的要求。急!!!!!
    他笑得很美, 电子竞赛
    vxwork 工程编译不过 d:\Tornado2.2\target\h\m2IfLib.h:26: parse error before `*'
    ccppc -c -g -mcpu=860 -ansi -fno-builtin -I.. -Id:\Tornado2.2\target\config\p3_mpc852_bsp-Id:\Tornado2.2\target\h -Id:\Tornado2.2\target\config\comps\src -Id:\Tornado2.2\target\src\drv -DCPU=PPC860 -D
    hellovla 嵌入式系统
    gps问题
    现在想要学习车载GPS技术,想了解一下现在GPS的研究方向还有现在流行的核心技术(包括软硬件),麻烦知道的说下,多谢了
    seewei 嵌入式系统
    S3C2450 + MLC FLASH 在开机LOGO中如何加进度条?????
    请教各位高手,如何在尽量不占用启动时间的前提下,在开机LOGO中加进度条?我看过扬创的开发板上加的进度条,完全是通过占用开机时间来换取的,而且FLASH是SLC的,启动速度快。不知道在MLC中有没好的办法?现在我手上机器,bootloader很快就启动完了,剩下的就进入加载驱动等一直到开机,这一段时间花费近10秒,开机LOGO至少要在bootloader启动后停留好多秒,于是想在bootloade
    mahai 嵌入式系统
    先楫半导体 HPM6750测评 Step4 (FreeRTOS+TinyUSB+LVGL) 综合示例
    0.由于在RT-Thread Studio上的lvgl示例的基础上增加TinyUSB组件有冲突,所以本次使用FreeRTOS进行开发1.首先在\hpm_sdk\samples\littlevgl\lv_demo_widgets的基础上调整CMakeLists.txt以增加tinyusb 和freertos的相关配置# Copyright 2021 hpmicro# SPDX-License-Ide
    arilink 国产芯片交流
    液晶显示驱动
    您好,我是北京迪文科技有限公司的刘玉龙,在网上看见贵公司开发多款仪器上面使用到了液晶,为了提高咱们公司产品档次或升级、希望关于驱动上面的事情跟您这边进行一下沟通,麻烦您了。我们公司最近推出的TFT驱动模组M600,这款模块的优势非常大,驱动模组提供的是RS232串口方式,通过协议来控制屏的显示,操作起来特别简单,界面部分由美工设计人员通过计算机设计图片便可以,而且以后产品升级起来特别方便,下位机的
    xiaojuan222 嵌入式系统

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved