• 本课程为精品课,您可以登录eeworld继续观看:
  • (b) PROTECTION AROUND SWIMMING POOLS - 680.22(A)(1) THRU (A)(5)​​​​​​​
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    WinCE环境下的屏幕录像程序?
    有谁知道WinCE环境下的屏幕录像程序?给我发一个yuanxiqiang@163.com
    kwoklee 嵌入式系统
    购买等离子彩电须注意的几个问题
    等离子显示屏PDP是一种利用气体放电的显示装置,这种屏幕采用了等离子管作为发光元件,在技术、结构和组成方面较其他显示方式领先一步。其工作机理类似于普通日光灯,电视彩色图像由各个独立的荧光粉像素发光综合而成,因此图像鲜艳、明亮、干净而清晰。另外,它最突出的特点是可以做到超薄,并轻易做到40英寸以上的完全平面大屏幕,而厚度不到100毫米。  在选购的时候注意以下几个问题: [size=0px]( W7
    绿草 淘e淘
    Altium Designer 09 蛇行等长布线
    蛇行等长布线技巧
    zhdming123 PCB设计
    阿莫做PCB需要注意的地方。。。
    1,线宽线距不少于7MIL2. 内孔径不少于4MM,并且以0.5MM递增3. 如果是很大的孔,如3.5寸电源插头那种,那需要做槽孔,不能用N个圆通孔来替代。4. 所有需要插入器件的孔的内径需要补偿0.15MM,用标准封装的(如:2.54间距的排针)也不例外。5. 板子的外框要单独画在机械层里,并且该机械层只能有板子的外框。(有些器件的封装里有机械层15,那么我们就挑过一个机械层画板子的外框,如机械
    youki12345 PCB设计
    【一步步啃POS机套件】之一, 背光IC使用电路
    背光IC型号为TPS61160,它的各项性能这里不再向大家介绍了,可以看其datasheet。值得注意的是,背光IC的一般拓朴结构都差不多,基本是BOOST型的,有一个参数很重要:参考电压Vfb,由于它的结构决定了,这个电压越低,效率越高!TI在这方面做得还不太好,我用过台湾的背光IC,它的电压做得相当低。画了它的电路图如下:[[i] 本帖最后由 dontium 于 2013-1-27 14:18
    dontium 模拟与混合信号
    DS1302问题请教
    最近在单片机上做了个时钟显示,时钟芯片用的是DS1302,但是仿真时DS1302的管脚没有反应,一个1302困扰了我好多天了,现在贴出源程序,请高手们指点指点。感激不尽!#include#include#include#define uchar unsigned char#define ds1302SCKP2_2 /*DS1302实时时钟时钟线引脚*/#define ds1302IOP2_3/*D
    weijing1225 嵌入式系统

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved