• 本课程为精品课,您可以登录eeworld继续观看:
  • CONDUCTORS FROM GENERATOR TERMINALS - 240.21(G)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    可重构技术
    可重构技术的基本特征和实现方法 (在多核处理器中的应用)可重构多核处理器的发展现状
    zhutn 嵌入式系统
    ATMEGA128内部参考电压准吗
    用内部参考电压作为基准,AREF引脚上是电压的值嘛,测出来有2.7伏,是不是不准呀,AVR单片机都要引入片外基准电压吗?
    jayce Microchip MCU
    疑惑:时钟初始化和协调问题
    扒了扒 stm32启动的时候,在进入main函数之前,进入一个systemInit函数,进行时钟频率初始化等工作,这个函数和 RCC_Config这个函数有什么不一样的吗?好像都是对时钟频率配置的啊,第二个问题:cpu读取外设的时候,cpu的工作时钟应该和外设的时钟是不一样的吧?怎么协调工作的?前辈们,能分析一下吗?
    craigtao stm32/stm8
    晶振脚位发黑了,怎么办?
    晶振脚位发黑是因为保存不当而出现晶振脚位氧化的情况,我们所看到的金属面位置有些许黑点,黑点正是因为金属部位与氧气接触,造成生锈的结果。  关于晶振的保存方法我们也不得不学着一些。我们要意识到晶振脚位氧化会给我们的工作带来什么样的损失。首先晶振脚位氧化,锡线和锡膏都无法正常焊接;此外晶振脚位氧化很容易造成晶振停振,性能较差,即为坏晶振。若库存中晶振脚位氧化为少数,我们可以采用以下办法使之焕然一新。 
    Aguilera 模拟与混合信号
    求兼职
    本人工作过两年 基本能够熟练使用MSP430和LPC1768、LPC1343单片机 以及熟练使用PROTEL画原理图和PCB现在在南京读研一希望又在在南京找一份兼职补贴补贴生活。
    c328604557 求职招聘
    纪念抗战爆发77周年,免费赠送VC5509A DSP板,寻找热血男儿
    [i=s] 本帖最后由 dontium 于 2014-7-10 11:56 编辑 [/i]先上图片:图片(板子)说明:板子为DSP图像处理板,5V供电,有JTAG接口位置,USB引出位置等。通电后自检正常。赠送说明:赠送主旨: 抵制日货。要求:1、 (以后)不参加日系产品的推广活动。2、 (以后)不购买(选择)日系产品(器件)。---在没有替代方案时此项无效。3、 支持国产。 --- 如果你是生产
    dontium 聊聊、笑笑、闹闹

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved