• 本课程为精品课,您可以登录eeworld继续观看:
  • GUEST ROOMS OR GUEST SUITES IN HOTELS AND MOTELS - 210.70(B)​​​​​​​
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    【设计工具】FPGA常犯错误集锦
    1.QuartusII对代码进行时序仿真时出现Error: Can't continue timing simulation because delay annotation information for design is missing.2.在下载运行的时候,出现下面的错误:Warning: The JTAG cable you are using is not supported for
    GONGHCU FPGA/CPLD
    IAR的奇怪问题,来一起讨论
    [i=s] 本帖最后由 liutogo 于 2015-1-24 22:24 编辑 [/i]不知道怎么了,在IAR里面新建的工程,所有的都.c文件都报警告,虽然不影响程序的运行,但就是看着不舒服。Warning[Pa050]: non-native end of line sequence detected (this diagnostic is only issued once) E:\Proje
    liutogo 嵌入式系统
    单片机延时方法总结
    [size=4][color=#000000][backcolor=white]实现延时通常有两种方法:一种是硬件延时,要用到定时器/计数器,这种方法可以提高CPU的工作效率,也能做到精确延时;另一种是软件延时,这种方法主要采用循环体进行。[/backcolor][/color][/size][size=4][color=#000000][backcolor=white][/backcolor][
    Aguilera 微控制器 MCU
    uS 计划预告 与 咨询
    uS的直播已经持续了一个多星期了。虽然“进展比较缓慢”,但是,它一直在我的预料中顺利进行。不过,我打算在直播的同时,“插播“ 这么一个小帖子。收集一下大家对它的看法和这种直播方式的感受。首先,先来个总体计划。本来这是打算明天才发的。
    辛昕 编程基础
    【藏书阁】电磁场计算中的时域有限差分法(王常清)
    [b]目录:[/b]第一章 绪论第二章 时域有限差分法基本原理第三章 吸收边界条件第四章 总场、散射场和入射平面波第五章 电磁波散射问题第六章 时域有限差分法的改进第七章 地磁波对人体作用的计算问题第八章 微波和光波线路的时域分析[b]详细信息:[/b]书名:电磁场计算中的时域有限差分法作者:王常清页数:382 页 大小:12.3M格式:pdf 版
    wzt 无线连接
    数字化焊机
    数字化焊机电源网讯 最近我一直在查这数字化焊机的资料,看到有些讨论数字化焊机的帖子,禁不住想出来谈一下自己的一点看法,不对的地方请大家多多指教。对于逆变焊机主电路来讲,实际上就是数字化的电路,所以说逆变焊机本身就已完成主电路的数字化.因此对于所谓的数字化焊机来讲,一般也就是针对控制电路部分来讲的。首先先分析一下逆变焊机控制系统的的主要组成部分,焊机控制部分主要分为人机接口部分和电源控制部分.人机接
    安_然 模拟电子

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved