• 本课程为精品课,您可以登录eeworld继续观看:
  • (b) OVERCURRENT RELAYS AND CURRENT TRANSFORMERS - 240.100(A)(1)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    如何用f5529来代替stm32?
    本人完全是新手,接到任务说要用f5529来代替stm32f103vct6完成一个电压源,同时要改写相应的程序(对应stm32的程序已有),完全没有接触过msp430,具体要怎么改写?从哪入手?具体要看一些哪部分的书?求大神指点。。。
    Gilliatt 微控制器 MCU
    求助CD4511驱动四位数码管显示程序
    单片机新手求助CD4511驱动四位数码管显示 ,不懂CD4511七个端口怎么就能驱动四位连体的数码管显示的,求高手 说明一下是怎么实现四位数的同时显示.............顺便说一下小弟想用c语言来编单片机的程序
    sundown 51单片机
    【晒经典】电子指南针,简单就是美!(第3、4季)
    [i=s] 本帖最后由 dontium 于 2015-1-23 12:45 编辑 [/i]电路功能:随着方向不同,发出不同频率的声音。特别适合盲人朋友使用的电子指南针。它的电路可以拆成两部分看。以中间的运放为界。左边:1、霍尔元件IC1,信号是UGN-3501M。说起霍尔元件可以说是传感界的一朵奇葩。它无需接触就可测量。这有啥?这解决了很多麻烦的问题哦。比方说,汽车的历程测量(你打的的money)
    zgjxncytl 模拟与混合信号
    Altium Designe-PCB设计入门(三)
    [b][size=4]Altium Designe-PCB设计入门(三)[/size][/b][size=4][/size][size=4]作者:pcb2008[/size][size=4][/size][size=4][b]创建一个新的PCB文件[/b]在将原理图设计转变为PCB设计之前,需要创建一个新的PCB和至少一个板外形轮廓(board outline)。在Altium Designer中
    ohahaha PCB设计
    关于裸机IIS应用 我要崩溃了。
    这是我的程序。帮我看看吧。弄了几天都还是没一点声音。小弟在此感谢了。#include "2440addr.h"#define L3C (1 190ns//GPB[4:2]=L3C:L3D:L3Mfor(i=0;i 500nsrGPBDAT |= L3C;//L3C=HrGPBDAT |= L3D;//L3D=Hfor(j=0;j 500ns}else//If data's LSB is 'L'{r
    voyage1999 嵌入式系统
    谁有124个脚minipci接口引脚定义图
    想查看有124个脚minipci接口引脚定义图。有个旧笔记本电脑上拆下的bcm4318的无线网卡想做个usb的,没用引脚图。
    caozhongxp 无线连接

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved