• 本课程为精品课,您可以登录eeworld继续观看:
  • PROTECTION IN ACCESSORY BUILDINGS - 210.8(A)(2)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    wince5.0和activesync连接不上
    从同事的机器上COPY过来的wince目录,在同事的PC上编译的系统拿到我这里可以连上ctivesync,但我的机子上编译出来的系统就是连接不上,要么显示“正在连接”,要么就是连接上后浏览不到移动设备上的内容。activesync用的是4.5的版本。
    xiaodage 嵌入式系统
    求教用C8051310单片机完成AD转换,用LED灯亮的数目表示信号功率的大小
    最近在折腾一个接收部分,射频信号经过混频后,输出一个50MHz左右的中频信号,用检波器检波得到电压,电压大概是大概是0到2.5V之间,可以直接进入单片机行吗?是不是应该接个放大器?我想用单片机完成AD转换后,用八个或者若干个LED灯亮的个数来表示电压的大小,比如0到0.5V,LED1亮,0.5到1V,LED2亮,以此类推。下面是我再网上找到的一个msp430f6638单片机实验程序,思路和我的差不
    面包所长 51单片机
    简易数字电容测量仪
    用单稳态触发器做的一个简易的电容测量仪。大概原理就是通过单稳态触发器的暂稳态时间来计算这个电容的大小,利用的公式是1.1Rc上图片啦作品背面100uf电容测试结果哈哈哈,重头戏,俺花的原理图,见笑见笑。。。。。。
    zhangkai0215 51单片机
    单片机学习课件
    参考学习啊!
    TSB11 单片机
    学模拟+ 《运算放大器噪声优化手册》 二
    [i=s] 本帖最后由 dontium 于 2015-1-23 11:47 编辑 [/i]运放噪声分析技术的目标:根据运放规格书上的信息来计算出运放电路的峰峰值输出噪声。三步近似法: (1)根据方程做一个简单的评估(2)利用spice模型做更精确的评估(3)通过测量来验证这些结果噪声分析的目标是确定其输出噪声的峰峰值,为了达到目地,我们需要考虑运放电流噪声、运放电压噪声、电阻热噪声用于噪声分析的实
    huixianfxt 模拟与混合信号
    求购 ——瑞萨RL78G14开发板 ——
    本人在用瑞萨RL78G14开发板测试无感无刷电机的电调时,不慎将仅有的一块RL78G14开发板烧坏,原因不明。唉,肠子都悔青了{:soso_e109:},为了能够将这个DIY电调继续搞下,在此向大家收购闲置的瑞萨RL78G14开发板。可以通过QQ(1165579525)或直接回帖联系我,thanks!!!!!!
    shiyongzhu 瑞萨电子MCU

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved