• 本课程为精品课,您可以登录eeworld继续观看:
  • RECEPTACLE OUTLETS INSTALLED IN INDOOR WET LOCATIONS - 210.8(B)(6)
  • 登录
课程介绍
相关标签: 电子系统
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

显示全部 ↓
推荐视频

    猜您喜欢

    推荐帖子

    【LDO常见术语1】line regulation 和load regulation
    线性调整率 Line Regulation  1、定义: 又称源效应或电网调整率,是指输出电压随输入电压的线性变化的波动,条件是全满载。(输入电压在额定范围内变化时,输出电压之变化率. )  Line Regulation(+)=(Vmax-Vnor)/Vnor  Line Regulation(-)=(Vnor-Vmin)/Vnor  Line Regulation=(Vmax-Vmin)/Vn
    zch_genius 电源技术
    步进电机加减速
    2812控制驱动器驱动步进电机,信号脉冲和方向脉冲控制电机,加减速就是改变脉冲频率,谁有加减速的算法程序,现在急用,自己编来不及了!
    aitingshu1988 DSP 与 ARM 处理器
    太炫酷了!柔性屏概念智能手表
    [size=5]柔性屏的概念智能手表 Bangle,太酷炫了[/size]
    qwqwqw2088 聊聊、笑笑、闹闹
    C2000 RMS计算求指点
    简单来说这段代码是用来做FIR+RMS计算的。FIR的部分是直接用TI的例程的。RMS算法部分是自己写了。AD采集得到数据由CLA读取中断和采样结果,并且进行数字滤波。RMS算法的部分就是每次滤波完的数据都求一次平方,并且累加。同时设定某一个阀值Vth,当电压超过Vth时认为是采样满了一个周期,得到将所得平方和开放求平均开方得到有效值。再输出到CLA的通讯RAM中。代码如下,内含错误若干。已经改了
    a828378 微控制器 MCU
    请问各位大神,在IAR编译器出现这个问题,如何处理?
    Error[e117]: Incompatible runtime models. Module APS specifies that '__code_model' must be 'banked', but module AF has the value 'near'
    qiutao6 无线连接
    PXA310的SPI控制MCP2515不能读取?
    采用的是PXA310的SPI控制MCP2515, 发送是正常的。通过命令字写到2515后,然后读芯片状态寄存器。功过示波器观察MISO脚信号是正常的,可是读PXA_SSDR寄存器却总是0。代码如下所示:for (i = 0; i PXA_SSDR = 0xff;while ((SPI_CtrlBlk.pSPIReg->PXA_SSSR & 0x00000010) != 0);recv[i] = (
    tylar 嵌入式系统

    推荐内容

    可能感兴趣器件

    完成课时学习+分/次

     
    EEWorld订阅号

     
    EEWorld服务号

     
    汽车开发圈

     
    机器人开发圈

    About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

    站点相关: 汽车电子 智能硬件

    北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

    电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2025 EEWORLD.com.cn, Inc. All rights reserved